|
Powell's Sales & Service
1305 Justus Blvd.
Clarks Summit, Pa. 18411
Phone: 570-587-2743
TollFree 888-44powell
Fax 570-586-6553
Hours:
Mon.-Fri. 7:30 to 5:00
Sat. 7:30 to 4:30
Sunday Closed
This page designed & maintained by
Michael Brelish.
Page was last edited
03/29/2007 03:39:52 PM
Copyright
2007 ©
Michael Brelish.
All Rights Reserved.
| |
New to Powell's in 2006 !
BUYERS
Gas Hopper
Spreaders
|
Part No. |
Description |
| 1400050SS |
1.8 cu. yd.
96" Gas Stainless Steel Hopper Spreader Kit, Std. Chute |
| 1400100SS |
1.8 cu. yd.
96" Gas Stainless Steel Hopper Spreader Kit, Ext. Chute |
IDEAL FOR MEDIUM AND HEAVY DUTY COMMERCIAL
APPLICATIONS.
General – All hopper spreaders are completely
self-contained, ultra-durable spreader units designed for ice
and snow control. The rugged design allows for use with salt,
sand and other materials. The complete assembly mounts easily
on pickup, dump and platform trucks making it ideal for
municipalities, shopping malls, industries, hospitals and
private contractors.
STEEL/STAINLESS STEEL MATERIAL HOPPER* – Electrically
welded 12-gauge ends and steel sides sloped at 45º are
constructed with channel formed top edges. 12-gauge vertical
supports add extra strength to the unit. The single lift point
on the cross support beam is located at the unit ’s center of
gravity to allow for easy loading and unloading. The floor is
constructed of 10-gauge steel.
*Stainless steel models feature high-quality grade 304
stainless steel components, including: Hopper, Hopper
Supports, Hopper Floor, Gussets, Spinner Chute Assembly,
Deflectors and Engine Hood.
POLYMER MATERIAL HOPPER – Rotationally molded
double-wall polymer unibody spreader with smooth angled walls
to maximize material flow. Features integrated positive
position mount system plus 4-piece ratchet tie-down kit. No
drilling required.
CONVEYOR – The conveyor is made of 12"wide all-steel
pintle chain with 3/16"x 3/4"cross bars. Chain strength is
11,000 lbs.per strand;22,000 lbs. total weight. The drive
sprockets are 6-tooth cast iron, on a 1-1/8" diameter shaft.
The conveyor chain has an adjustment range of 3-1/2". The
drive shaft has heavy-duty, sealed, self-aligning ball
bearings with grease fittings. The idler drum has heavy-duty
1" diameter ball bearings.
CONVEYOR GEAR CASE – Gear is constructed of aluminum
bronze, worm gear is hardened steel and ground. Housing is
made of durable cast iron. Gear ratio is 20:1 with 1" input
shaft and 1-1/8"output shaft on tapered roller bearings.
FEEDGATE – Lever operated with a friction lock for
accurate adjustment.
SPINNER CHUTE ASSEMBLY** – A polymer disc with four
fins is connected to a 3/4"diameter shaft secured on two
pillow block bearings. The spreading material is guided from
the conveyor to the spinner plate through an enclosed 12-gauge
chute with internal and external deflectors. Adjustable
deflectors allow for complete directional spread control and
full or compact spread. Total spread radius ranges from 2' to
25'. The extra wide rear deflector protects the rear and under
carriage of the vehicle.
**Stainless steel & polymer hoppers feature high-quality
grade 304 stainless steel Spinner Chute Assembly, Deflectors
and Engine Hood.
ENGINE – Heavy-duty 10.5 horsepower
industrial/commercial Briggs & Stratton gasoline engine.
Engine comes equipped with alternator and 12 volt electric
starter with in-cab start/stop and electric throttle control
(standard). Entire engine is completely protected by the
convenient hinged hood.
ELECTRIC THROTTLE CONTROL – Throttle control unit
allows for full-range of throttle settings,including idle and
full choke,via the in-cab hopper control box. Use of electric
throttle control eliminates cable freezing, binding and
breaking.
CLUTCH – 12 volt DC electric clutch has a
three-position in-cab switch, for greater control and material
economy. Also allows for low speed operation and spot
spreading.
72" Spreaders – Body Side Length, 6'; Overall Length,
89"; Capacity Struck, 1.3 cu.yd.; Capacity Rounded, 1.6 cu.yd.;
Width, 47"; Height, 32 –1/2"; Recommended Use, 3/4 or 1-Ton
Trucks.
96" Spreaders – Body Side Length, 8'; Overall Length,
113"; Capacity Struck, 1.8 cu.yd.; Capacity Rounded, 2.1 cu.yd.;
Width, 47"; Height, 32 –1/2"; Recommended Use, 3/4 or 1-Ton
Trucks.
120" Spreaders – Body Side Length, 10'; Overall Length,
137"; Capacity Struck, 2.3 cu.yd.; Capacity Rounded, 2.7 cu.yd.;
Width, 47"; Height, 32–1/2"; Recommended Use, Heavy-duty
flatbed or long dump Trucks. |
|
|
|
Under Tailgate Spreaders
 |
|
Under Tailgate Spreaders |
|
Part No. |
Description |
|
92420A |
96"
Direct Drive Under Tailgate Spreader |
|
92420SSA |
96"
304 Stainless Steel Direct Drive Under Tailgate Spreader
|
|
92430SSA |
96"
304 Stainless Steel Spreader w/5:1 Reduction Ratio Gearbox
|
|
|
Under Tailgate Spreaders
HEAVY DUTY COMMERCIAL AND MUNICIPAL APPLICATIONS.
Available in orange powder coated carbon steel or stainless
steel models.
•Direct drive operation reduces numbers of moving
parts,assuring dependable service.
•Under tailgate mounting allows normal use of dump body
without interference from spreader.
•Rugged 7-gauge trough has 3-point hinged bottom cover that
provides easy access to entire auger assembly for easy,one-person
cleanout.
•Spreads from 4' to 40' of rock salt, free-flowing granular
materials or chemicals.
•Auger is supported by 1-1/4"steel shaft ends and has right
and left flighting to the discharge port delivering a
continuous,consistent flow of spreading material.
•Sealed,self-aligning 1-1/4"diameter radial bearings with
grease fittings.
•Low-speed,high-torque orbital motors
•Spreader assemblies come with material trough, auger
assembly, spinner and auger motors, spinner assembly,
polyurethane spinner and mounting plates (as shown in photo)
•Hydraulic safety lockout system -New |
|
|
|
|
Sales-Service-Rental-Parts